One of the isotope pairs widely used in geology is the decay of 40K to 40Ar ( potassium to argon). 40K is a radioactive isotope of potassium that is present. Radiometric dating is used to estimate the age of rocks and other objects based on the fixed decay rate of radioactive isotopes. Learn about. Recognition that radioactive decay of atoms occurs in the Earth was Some examples of isotope systems used to date geologic materials.
This predictability allows the relative abundances of related nuclides to be used as a clock to measure the time from the incorporation of the original nuclides into a material to the present. Accuracy of radiometric dating[ edit ] Thermal ionization mass spectrometer used in radiometric dating. The basic equation of radiometric dating requires that neither the parent nuclide nor the daughter product can enter or leave the material after its formation.
The possible confounding effects of contamination of parent and daughter isotopes have to be considered, as do the effects of any loss or gain of such isotopes since the sample was created. It is therefore essential to have as much information as possible about the material being dated and to check for possible signs of alteration.
Alternatively, if several different minerals can be dated from the same sample and are assumed to be formed by the same event and were in equilibrium with the reservoir when they formed, they should form an isochron. This can reduce the problem of contamination. In uranium—lead datingthe concordia diagram is used which also decreases the problem of nuclide loss.
Finally, correlation between different isotopic dating methods may be required to confirm the age of a sample. For example, the age of the Amitsoq gneisses from western Greenland was determined to be 3. The procedures used to isolate and analyze the parent and daughter nuclides must be precise and accurate. This normally involves isotope-ratio mass spectrometry. For instance, carbon has a half-life of 5, years.
After an organism has been dead for 60, years, so little carbon is left that accurate dating cannot be established.
On the other hand, the concentration of carbon falls off so steeply that the age of relatively young remains can be determined precisely to within a few decades. Closure temperature If a material that selectively rejects the daughter nuclide is heated, any daughter nuclides that have been accumulated over time will be lost through diffusionsetting the isotopic "clock" to zero. The temperature at which this happens is known as the closure temperature or blocking temperature and is specific to a particular material and isotopic system.
These temperatures are experimentally determined in the lab by artificially resetting sample minerals using a high-temperature furnace. As the mineral cools, the crystal structure begins to form and diffusion of isotopes is less easy. At a certain temperature, the crystal structure has formed sufficiently to prevent diffusion of isotopes.
This temperature is what is known as closure temperature and represents the temperature below which the mineral is a closed system to isotopes. Thus an igneous or metamorphic rock or melt, which is slowly cooling, does not begin to exhibit measurable radioactive decay until it cools below the closure temperature.
The age that can be calculated by radiometric dating is thus the time at which the rock or mineral cooled to closure temperature. This field is known as thermochronology or thermochronometry. The age is calculated from the slope of the isochron line and the original composition from the intercept of the isochron with the y-axis.
The equation is most conveniently expressed in terms of the measured quantity N t rather than the constant initial value No. The above equation makes use of information on the composition of parent and daughter isotopes at the time the material being tested cooled below its closure temperature.
This is well-established for most isotopic systems. Plotting an isochron is used to solve the age equation graphically and calculate the age of the sample and the original composition. Modern dating methods[ edit ] Radiometric dating has been carried out since when it was invented by Ernest Rutherford as a method by which one might determine the age of the Earth. In the century since then the techniques have been greatly improved and expanded.
Radiometric dating - Wikipedia
The mass spectrometer was invented in the s and began to be used in radiometric dating in the s. It operates by generating a beam of ionized atoms from the sample under test. The ions then travel through a magnetic field, which diverts them into different sampling sensors, known as " Faraday cups ", depending on their mass and level of ionization.
On impact in the cups, the ions set up a very weak current that can be measured to determine the rate of impacts and the relative concentrations of different atoms in the beams. Uranium—lead dating method[ edit ] Main article: Uranium—lead dating A concordia diagram as used in uranium—lead datingwith data from the Pfunze BeltZimbabwe.
This scheme has been refined to the point that the error margin in dates of rocks can be as low as less than two million years in two-and-a-half billion years. Zircon has a very high closure temperature, is resistant to mechanical weathering and is very chemically inert.
Zircon also forms multiple crystal layers during metamorphic events, which each may record an isotopic age of the event. This can be seen in the concordia diagram, where the samples plot along an errorchron straight line which intersects the concordia curve at the age of the sample.
Samarium—neodymium dating method[ edit ] Main article: Samarium—neodymium dating This involves the alpha decay of Sm to Nd with a half-life of 1.
Accuracy levels of within twenty million years in ages of two-and-a-half billion years are achievable. Potassium—argon dating This involves electron capture or positron decay of potassium to argon Potassium has a half-life of 1. Rubidium—strontium dating method[ edit ] Main article: Rubidium—strontium dating This is based on the beta decay of rubidium to strontiumwith a half-life of 50 billion years.
This scheme is used to date old igneous and metamorphic rocksand has also been used to date lunar samples. Closure temperatures are so high that they are not a concern.
Rubidium-strontium dating is not as precise as the uranium-lead method, with errors of 30 to 50 million years for a 3-billion-year-old sample. Uranium—thorium dating method[ edit ] Main article: Uranium—thorium dating A relatively short-range dating technique is based on the decay of uranium into thorium, a substance with a half-life of about 80, years.
It is accompanied by a sister process, in which uranium decays into protactinium, which has a half-life of 32, years. Living things are in equilibrium with the atmosphere, and the radioactive carbon dioxide is absorbed and used by plants. The radioactive carbon dioxide gets into the food chain and the carbon cycle.
All living things contain a constant ratio of Carbon 14 to Carbon At death, Carbon 14 exchange ceases and any Carbon 14 in the tissues of the organism begins to decay to Nitrogen 14, and is not replenished by new C The change in the Carbon 14 to Carbon 12 ratio is the basis for dating. The half-life is so short years that this method can only be used on materials less than 70, years old.
Archaeological dating uses this method. Also useful for dating the Pleistocene Epoch Ice Ages. Assumes that the rate of Carbon 14 production and hence the amount of cosmic rays striking the Earth has been constant through the past 70, years.
These trails are due to the spontaneous fission of uranium. Enlarge tracks by etching in acid so that they may be visible with light microscope See readily with electron microscope Count the etched tracks or note track density in an area Useful in dating: Micas up to 50, tracks per cm squared Tektites Natural and synthetic manmade glass Reheating "anneals" or heals the tracks.